How to Configure Network Static IP Address on RHEL/CentOS 8/7

The scope of this tutorial is to explain how we can edit and make changes to Network Configurations on RHEL/CentOS 8/7 from the command line only, and, more specifically how we can set up a Static IP address on network interfaces using system network-scripts, which is a must be configured to serve Internet-facing network services, and how to configure or change RHEL/CentOS system hostname.

Configure Network Interface in CentOS 7
Configure Static IP in Linux

Also will show you, how we can manage or disable unwanted system services, such as Network Manager, which is no longer needed in-case you use a manual static IP configured on network scripts, Avahi-Daemon which is, also, not needed on a server and represents a seriously security gap, unless you installed the server on your Laptop and you want to instantly browse your network for other services, and on the final will present you Network Manager Text User Interface – nmtui, a system utility that can ease the job of editing your system network settings with advanced Interface configurations like creating Bond, Bridge, Team and VLAN Interfaces.


Also, be aware that most of the configurations offered by editing system files should not be performed from a remote location using SSH service until you establish a continued and reliable network connection using a fixed IP address.

On this page

Step 1: Disable Unwanted System Services in CentOS

1. Before actually starting to do anything we need to make sure that our system has some necessary editing and networking tools like netstat, ifconfig, wget, curl, and lsof installed, some of them will not be used on this step but it’s better to have them installed for future configurations.

# yum install nano wget curl net-tools lsof
Install Networking Tools in CentOS
Install Networking Tools in CentOS

2. After the tools have installed run ifconfig to get your Network Interfaces settings and status, and, then run netstat or lsof command to check what services are running by default on our server.

# ifconfig
# netstat -tulpn
# lsof -i
Check Network Interfaces and Services Status
Check Network Interfaces and Services Status

3. The netstat command output is pretty self-explanatory and shows a list of sockets associated with their running program name.

If, for example, our system will not be used as a mail service you can stop Postfix master daemon which runs on localhost and, also stop and disable other unwanted services using the following commands – the only service I advise not to stop or disable for now is SSH if you need remote control over the server.

Stop Postfix Service
# systemctl stop postfix
# systemctl disable postfix
# systemctl status postfix
Stop Postfix Service
Stop Postfix Service
Stop Avahi Daemon Service
# systemctl stop avahi-daemon
# systemctl disable avahi-daemon
# systemctl status avahi-daemon
Stop Avahi Daemon
Stop Avahi Daemon

4. You can, also, use old init commands to stop or disable services but since Red Hat now implements systemd process and service management, you should better get used to systemctl commands and use it often.

If you use Arch Linux then it should be a piece of cake to switch to systemd – although all init commands now are linked and pass-through systemd filter.

# service postfix stop
# chkconfig postfix off

5. If you want to get a list of all started services run the service command and for an exhaustive report use systemctl.

# service --status-all
# systemctl list-unit-files
List All Services in Linux
List All Services in Linux
List All Services Report
List All Services Report

6. To manage services run the systemctl command using the most important switches: start, stop, restart, reload, disable, enable, show, list-dependencies, is-enabled, etc. followed by your service name.

Also, another important feature that the systemctl command can also run on a remote server through SSH service on a specified host using -H option and perform the same actions as locally.

For example, see the command and screenshot below.

# systemctl -H remote_host start remote_service
Run systemctl on Remote Server
Run systemctl on Remote Server

Step 2: Configuring Static IP Address on CentOS

7. Before start editing Network Interface Card system files make sure that from now on and until you set static IP, you have physical or any other type of access to your server, because this step requires bringing down your network interface and connections.

Although it can be done smoothly without disrupting your connectivity and activate connection after reboot. There is no way you can test it before reboot if you only have a single NIC attached. Still, I will present to you with the entire method and indicate the steps needed to be avoided in case you want to maintain your connectivity and test it afterward.

8. Now move to /etc/sysconfig/network-scripts/ path, open and choose your Network Interface you want to assign static IP for editing – to get all NICs names to use ifconfig or IP command as shown.

# ifconfig
# ip addr
Check Network Interface Name
Check Network Interface Name

9. Next, use the following network template to edit the file and make sure that the ONBOOT statement is set on YES, BOOTPROTO is set to static or none and don’t change HWADDR and UUID values provided by default.

# nano /etc/sysconfig/network-scripts/ifcfg-enp0s3

Make the following changes as shown.

Configure IP Address in CentOS 8
Configure IP Address in CentOS 8

10. After finishing editing the file, close it, and move to resolv.conf file if you want DNS servers enabled system-wide.

# nano /etc/resolv.conf

Here just add your DNS servers using nameserver statement.


11. Now Network Interface is configured with a static IP, the only thing remaining is to restart your network or reboot your system and use ifconfig or IP command to view the IP address and test configuration using ping command.

# systemctl restart NetworkManager

NOTE: After restart use the newly static IP address configured to perform remote login with SSH.

# systemctl status NetworkManager
# ifconfig
# ip addr show
Check New IP Address
Check New IP Address

Step 3: Setting Hostname in CentOS

12. To adjust system hostname system-wide, open hostname and hosts file located on /etc path and edit both the following way.

Hostname File
# nano /etc/hostname

Here you can add just the name of the system but it’s a good idea to append the .dot domain to.

Hosts File
# nano /etc/hosts

Here add the same hostname as above on the line before the localhost.localdomain statements. server.tecmint.lan localhost.localdomain …
Set Hostname in CentOS 7
Set Hostname in Linux

Alternatively, you can set hostname using the hostnamectl command as shown.

# hostnamectl -set-hostname tecmint.lan

13. To test if your hostname is correctly set use hostname command.

# hostname -s # For short name
# hostname -f # For FQDN mame

Step 4: Set Static IP Address on CentOS Using Nmtui Tool

14. NetworkManager Text User Interface (TUI) tool, nmtui, is an RHEL intuitive tool which provides a text interface to configure networking by controlling Network Manager, which helps to edit advanced network settings such as assign static IP addresses to Network Interfaces, activate or disable a connection, edit WI-FI connections, set your system hostname or create advanced Network interfaces like InfiniBand, bond, bridge, team or VLAN.

NetworkManager-tui is installed by default in RHEL/CentOS 7.0, but if for some reason its missing issue the following command to install it.

# yum install NetworkManager-tui

14. To start Network Manager Text User Interface run the nmtui command and use TAB or arrow keys to navigate through and press Enter to select an option. If you want to directly edit or connect a specific interface run the following options.

# nmtui edit enp0s3
# nmtui connect enp0s3
Configure Static IP in CentOS
Configure Static IP in CentOS

If you want to set static IP you can, also, use Network Manager Text User Interface as a facile alternative to actually edit network interfaces files, with a limited number of options that method has to offer, but make sure Network Manager service is enabled and started on your system.

Posted by Contributor